• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a doable job for most homeowners. However, if the screw holes are stripped and aren't able to hold screws, you might have to put in wood glue and dowels before you can install the hinge.

Before you do this, however, brush away the surface rust. This will allow the dowels to stay in place and give them a solid foundation to rest on.

Eliminating the Hinges

Most hinges on doors can be removed, which makes it easier to move the door from one side to the next or take the entire door window blown off hinges of the frame if need be. Anyone who is patient can remove the hinges, but you must be aware of what to do.

If the hinges are painted you will need to remove the paint prior to trying to remove the pins. It is possible to scratch your door if you do not remove the paint. Put the hinges in the stainless steel pot and fill it with water to the point that the hinges are submerged. Let the hinges sit in the pan for 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

After the pins have been loose, remove the hinges and frame from the door. You can make use of a screwdriver to get the job done, but it is recommended that you make use of a magnetic screwdriver for this project. This type of screwdriver has been specifically designed to take out metal screws and aid you in getting the job accomplished much faster.

It is a good practice to spray lubricant onto the hinges prior to attempting to remove them. A simple lubricant can help the process move along quickly and aid in the removal of the pins and screws. This kind of lubricant is able to be found in most hardware stores and home improvement stores.

It is important to keep in mind that the number of door hinges you will need will vary depending on the type of door and the settings. Heavy doors and solid-core doors will need more hinges, while hollow-core doors that weigh less might only require two or three hinges.

Understanding the various types of hinges can help you decide which one is the best for your particular situation. Exterior hinges are typically designed to support the weight of the door and interior window hinges replacement require to handle heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may become loose and start to sag or hang crookedly. It can be a big issue, but the solution is usually simple. A simple retightening will usually resolve the issue. If the screw holes have been ripped out, it can be difficult to fix. A wood dowel could be used to tighten these holes once more.

Begin by drilling out the hole you had previously made using an appropriate drill bit close to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a snug fit, the dowel must be cut to the same length as the screw. After that, reinstall the screw and tighten it to the desired level of tightness. If the door still has an tendency to get stuck the door, then add a second dowel to the gap and repeat the process. Make sure to close the door slowly in order to verify the clearances at the perimeter after each adjustment.

Another option is to use an old-fashioned wood plug instead of dowel. This is also a viable option however it may take some time to set up. You can tap in a piece of wood that has been whittled to the proper size. If you don't own a woodworking instrument or toothpicks, you can make use of toothpicks or wooden matchsticks.

After you've reinstalled your new screw, use a countersink bit to make the hole for the head of the screw smaller so that it won't rub against the edge of the door when it's open and closed. This will make it easier to tighten the screws when reinstalling hinges.

After installing the hinge again, you should lubricate the hinge with dry lubricant. This will help prevent it from getting stuck in the future. Products like PB Blaster or Liquid Wrench are great alternatives. You should apply a light coat and wait for approximately 15 minutes to get into the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace upvc energy efficient window hinge the hinges on your door, you could do a few simple repairs. The first step is to ensure that the screws holding the hinge plate to the door and frame are tight. If they are loose, tighten the screws with a power drill or screwdriver. Be cautious not to tighten the screws to the point that they begin to create gaps at the trim joints, or even worse remove the threads.

If the issue is that the hinge plates are separated from the door and jamb and jamb, you can fix the hinges by applying wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks provide a solid base for the screws and to prevent the plates from shifting when you drive them into the holes. Let the glue dry before attaching the hinge.

The screws may also be damaged or missing. This can be fixed by replacing the screws with longer ones. Use a drill bit that is the same size as the screw hole to prevent drilling into the jamb or hinge.

Close the door once you've reattached the hinge and measure the gap between the frame and the door. The gap should be about the thickness of a penny or less if an older door was hung incorrectly. If the hinges were put in place correctly, this should not be a problem.

If you discover that the hinges are still loose, try putting an extra thicker shim between the hinge plate and the mounting surface to add some extra space. You can also take off the hinge pin, then pound it down with a hammer to tighten it up or choose the hinge of a different type. You can also lubricate your hinges with mineral oil or jojoba in order to reduce friction hinges for upvc windows and hold them in place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

The friction generated by the double glazed window hinge's constant motion draws dust particles. If there is no regular cleaning or lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. In the end the hinge becomes stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication, and inspection can preserve the quality of a hinged door and ensure their proper function.

Examine the hinges for signs of corrosion. If the rust is so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, begin by brushing off any loose rust with steel wool and a wire brush. Then, apply a commercial rust remover or homemade solution like lemon juice on the hinge. Let the rust remover remain on the hinge for several minutes to dissolve and penetrate any remaining corrosion.

If you do not want to spend the money and time replacing hinges, tightening the screws will make the hinges functional again. If you've sanded the screw holes however, it might be necessary to add an wooden dowel or shim to the hinge. Dowels made of wood are round pieces of wood in the form of rods that are available in different lengths and diameters. You can find them at home improvement centers or woodworking supply shops, or online.

A shim can also be made from plastic or metal, based on the type of hinge you have. To make a dowel, cut a piece made of wooden dowel or another sturdy material to the size you want. You can then dip the dowel in carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in place.

Before you begin cleaning the hinges, put down a towel or a paper towel to shield floors and other surfaces from drips and spills that could happen. After the area has been secured and dry, clean the hinges using an absorbent sponge or a soft cloth coated with a mild cleaner or vinegar to get rid of built-up dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach hard-to-reach spots in crevices or tight areas.